服務熱線:
400-879-1999
欄目導航
聯系我們
服務熱線
400-879-1999
電話:400-879-1999
地址:山東省萊州市206國道與308省道交叉口東南50米
當前位置:首頁 > 攪拌車資訊 > 常見問題 > 自動上料攪拌車發動機水溫過高的解決方法
自動上料攪拌車發動機水溫過高的解決方法
來源:http://www.wtiqradio.com發布日期:2020-07-27   瀏覽量:
 
自動上料攪拌車屬于特種專項作業車輛,它有特定的工作環境,發動機水溫難免會有過高的的時候。自上料攪拌車發動機水溫過高,有的會造成爆管爆水箱,再嚴重些造成沖缸墊,缸蓋變形。如果再繼續行駛,則有拉缸的可能,那么自動上料攪拌車發動機水溫過高的解決方法;
Automatic feeding mixer belongs to special special operation vehicle, it has a specific working environment, the engine water temperature will inevitably be too high. In some cases, the water temperature of the cylinder head will burst seriously. If you continue to drive, there is the possibility of cylinder pulling, then the solution of excessive engine water temperature of automatic feeding mixer truck
一、解決自動上料攪拌車發動機水溫過高的方法
1、 Solution to the problem of high water temperature in the engine of automatic feeding mixer
1、自動上料攪拌車在普通公路上發動機出現了過熱,應該盡快地降低車速,把汽車駛到樹蔭下,或駛到相對比較涼快的地方,把汽車停下來,但這時候不要急于熄火。
1. The engine of the automatic feeding mixer truck is overheated on ordinary roads. It is necessary to reduce the speed as soon as possible, drive the vehicle into the shade of trees, or drive to a relatively cool place, and stop the vehicle, but do not rush to turn off the engine at this time.
2、打開發動機罩蓋,讓發動機怠速運轉,等待發動機溫度逐漸恢復正常。在發動機水溫恢復正常之后,將發動機熄火,然后再等待一段時間,直到發動機的水溫充分地下降了之后,再檢查發動機的冷卻水量。
2. Open the engine cover, let the engine idle and wait for the engine temperature to gradually return to normal. After the engine water temperature returns to normal, turn off the engine, and then wait for a period of time until the water temperature of the engine drops sufficiently, and then check the cooling water volume of the engine.
3、這時候自動上料攪拌車發動機的冷卻水量可能大都嚴重不足。按著規定量把冷卻水補足之后,再檢查一下冷卻系統,確認沒有其他故障之后,可以起動發動機,繼續行駛。也要檢查一下水箱百葉窗是不是被異物堵塞,風扇葉的工作情況,發動機皮帶是否打滑,發動機水泵工作情況等。
3. At this time, the cooling water of the engine of the automatic feeding mixer may be seriously insufficient. After making up the cooling water according to the specified amount, check the cooling system again, and after confirming that there are no other faults, you can start the engine and continue driving. Also check whether the louver of water tank is blocked by foreign matters, the working condition of fan blade, whether the engine belt slips or not, and the working condition of engine water pump.
4、如果在高速公路上出現了發動機過熱,必須立刻把暖風全部打開并打開車窗,這時車廂內將熱得像地獄一樣。由于有暖風幫助冷卻水散熱,能使冷卻水溫大幅度地下降。這樣可以持續開車,就近找到高速公路的出口,將攪拌車駛到安全的場所停下來。接下來,只要按照上述的方法,使發動機的溫度降下來就行。注意,不要把攪拌車停在路邊,以免影響交通或被撞車,必須把攪拌車停在安全的場所。
4. If the engine overheats on the highway, you must turn on all the warm air and open the windows immediately. At this time, the car will be as hot as hell. Due to the warm air to help the cooling water dissipate heat, the cooling water temperature can be greatly reduced. In this way, you can continue to drive, find the exit of the expressway nearby, and drive the mixer to a safe place to stop. Next, as long as the above method, so that the engine temperature down on the line. Note that it is best not to park the mixer on the side of the road, so as not to affect the traffic or be hit. The mixer must be parked in a safe place.
因此發現自動上料攪拌車發動機水溫過高一定要采取措施,避免攪拌車出現嚴重故障,為了大家更好的了解相關的知識,下面小編和大家講解一下自上料攪拌車發動機水箱溫度過高的因素,及發動機的保養方法,希望可以幫助到大家。
Therefore, it is necessary to take measures to avoid serious failure of the mixer when it is found that the water temperature of the engine is too high. In order to better understand the relevant knowledge, the following editor will explain the factors that cause the engine water tank temperature to be too high and the maintenance methods of the engine, hoping to help you.
?

萊州中科聚峰機械有限公司
電話:15053524111 地址:山東省萊州市206國道與308省道交叉口東南50米
聚峰機械專注生產銷售混凝土全自動攪拌車,小型混凝土自動攪拌車,自進料混凝土攪拌車,平口攪拌車,廠家直銷,型號齊全,經久耐用,質優價廉;以規范的管理為依托,以專業的技術為支持,安全可靠,讓您放心選擇!

日本无吗无卡v免费清高清