服務熱線:
400-879-1999
欄目導航
聯系我們
服務熱線
400-879-1999
電話:400-879-1999
地址:山東省萊州市206國道與308省道交叉口東南50米
當前位置:首頁 > 攪拌車資訊 > 常見問題 > 自動上料攪拌車使用過程中鋼板容易破裂的原因是什么?
自動上料攪拌車使用過程中鋼板容易破裂的原因是什么?
來源:http://www.wtiqradio.com發布日期:2020-08-10   瀏覽量:
 
自動上料攪拌車的前鋼板由九塊組成。許多人報告說,自動攪拌上料機的和第二部分在使用過程中容易破裂是什么原因?
The front steel plate of the automatic mixing and feeding machine is composed of nine pieces. Many people have reported that the first and second parts of the automatic mixing and feeding machine are easy to crack during use?
(1)過度使用緊急制動器。在山上行駛時,在下坡路上使用緊急制動器可能會損壞前板。由于制動力,自動攪拌上料機的大部分負荷質量得到前板簧的促進和接受。結果,可能發生片簧的疲勞損壞。建議使用排氣制動器以減少緊急制動。
(1) Excessive use of emergency brakes. Using the emergency brake on a downhill road may damage the front panel when driving on a hill. Due to the braking force, most of the load mass of the automatic mixing feeder is promoted and accepted by the front leaf spring. As a result, fatigue damage of the leaf spring may occur. Exhaust brakes are recommended to reduce emergency braking.
(2)前輪制動調整太緊。如果后輪制動性能不佳,或者發生突然問題,請使用緊急制動器并通過過度沖擊破壞前板簧。
(2) Front wheel brake adjustment is too tight. If the braking performance of the rear wheels is poor or sudden problems occur, use the emergency brake and destroy the front leaf spring by excessive impact.
(3)路面不好,超載,超速,對前板簧施加過大的沖擊力,容易造成損壞。
(3) The road surface is not good, overload, overspeed, and the front leaf spring is subject to excessive impact force, which is easy to cause damage.
(4)前板簧經常長時間過載,降低彈性和剛性,并因疲勞而損壞。
(4) The front leaf spring is often overloaded for a long time, which reduces elasticity and rigidity, and is damaged due to fatigue.
(5)更換低質量的板簧。刀片彎曲不符合標準。由于鋼板材料不好或熱處理不好,應力變得不均勻和斷裂。
(5) Replace the low quality leaf spring. The blade bending does not meet the standard. Due to the poor material or heat treatment of steel plate, the stress becomes uneven and fracture.
為防止自動攪拌上料機前板簧的和第二塊自動裝載,我們建議采用以下方法:
In order to prevent the automatic loading of the first and second pieces of the front leaf spring of the automatic mixing feeder, the following methods are recommended:
(1)檢查時間,確保板簧良好潤滑,并正確調整車輛制動器。
(1) Check the time to ensure that the leaf spring is well lubricated and the vehicle brake is adjusted correctly.
(2)減少緊急制動器的使用,增加發動機排氣制動器的使用,均勻地施加載荷而不會過載。
(2) Reduce the use of emergency brake, increase the use of engine exhaust brake, evenly apply load without overload.
(3)更換前鋼板時,必須使用優質鋼板,以確保彎曲度符合要求。使用山東彈簧廠和重慶彈簧廠生產的板簧。
(3) When replacing the front steel plate, high-quality steel plate must be used to ensure that the bending meets the requirements. It is better to use the leaf spring produced by Shandong spring factory and Chongqing Spring Factory.
(4)在不平坦的道路上行駛或下坡行駛時,需要控制自動攪拌上料機的速度并在曲線上行駛。不要急于過快。
(4) When driving on uneven road or downhill, it is necessary to control the speed of automatic mixing feeder and drive on the curve. Don't rush too fast.
自動攪拌上料機傳動油品質檢測方法
Quality inspection method for transmission oil of automatic mixing and feeding machine
1.將自動攪拌上料機放在平坦的表面上并擰緊手制動器。
1. Place the automatic mixing feeder on a flat surface and tighten the hand brake.
2.讓發動機空轉幾分鐘。
2. Let the engine idle for a few minutes.
3.踩下制動踏板并轉動操縱桿前后移動。將每個齒輪移動幾秒鐘以填充變矩器和所有帶液壓油的換檔執行器。,將操縱桿轉到停車位置。
3. Step on the brake pedal and turn the control lever to move forward and backward. Move each gear for a few seconds to fill the torque converter and all shift actuators with hydraulic oil. Finally, turn the lever to the park position.
4.從加注管上取下自動量油尺,將清潔的量油尺插入加油管并將其拉出以檢查量油尺的油位。
4. Remove the automatic dipstick from the filler tube, insert the clean dipstick into the filler tube and pull it out to check the oil level of the dipstick.
在檢查或排除自動攪拌上料機故障之前,首先檢查變速箱油位和油質。換檔桿必須處于P位置,發動機應在空轉時運轉至少幾分鐘,液體將達到正常工作溫度,并且車輛必須停在水平面上以確保差速器和節氣門之間的油位。通常傳輸是穩定的。
Check the oil level and oil quality of the gearbox before checking or troubleshooting the automatic mixing feeder. The shift lever must be in the P position, the engine should be running at idle for at least a few minutes, the fluid will reach normal operating temperature, and the vehicle must be stopped on a level surface to ensure the oil level between the differential and the throttle. Usually the transmission is stable.
自動上料攪拌車的鋼板斷裂和傳動油質量檢查問題介紹就是這樣了,希望對你有幫助。
Automatic mixing feeder steel plate fracture and transmission oil quality inspection problem introduction is like this, hope to help you.
?

萊州中科聚峰機械有限公司
電話:15053524111 地址:山東省萊州市206國道與308省道交叉口東南50米
聚峰機械專注生產銷售混凝土全自動攪拌車,小型混凝土自動攪拌車,自進料混凝土攪拌車,平口攪拌車,廠家直銷,型號齊全,經久耐用,質優價廉;以規范的管理為依托,以專業的技術為支持,安全可靠,讓您放心選擇!

日本无吗无卡v免费清高清